JMB585 Chip 5 Port SATA 3.0 to PCIe Expansion Card 4X Gen 3 PCI Express SATA Adapter SATA 3 Converter with Heat Sink for HDD SSD

Certification:NONE
Origin:CN(Origin)
Package:Yes
Model Number:AC4558
Type:Add On Cards
Interface Type:PCI Express
SATA1:sata controller
SATA2:pcie sata
SATA3:pci-e sata
SATA4:sata hub
SATA5:ssd sata 3 adapter
SATA6:pcie sata3 adapter
SATA7:pci e to sata adapter
SATA8:sata pci express card
SATA9:sata pcie card
SATA10:sata card
SATA11:pcie to sata 3.0 card
SATA12:pci e sata card
SATA13:pcie to sata card
SATA14:ssd pcie adapter
SATA15:pci express ssd adapter
SATA16:pcie ssd adapter
SATA17:ssd pci express card
SATA18:5 ports PCIE sata card

JMB585 Chip 5 Port SATA 3.0 to PCIe Expansion Card 4X Gen 3 PCI Express SATA Adapter SATA 3 Converter with Heat Sink for HDD SSD
About Description:
Features:
Compliant with Serial ATA 3.0 specification, backward compatible with SATA2.0 SATA1.0
Compliant with PCI-Express v3.0 specification, backward compatible with PCI-Express v2.0 v1.0.
Supports communication speeds of 6.0 Gbps, 3.0 Gbps and 1.5 Gbps
Support Gen 1i, Gen 1x, Gen 2i, Gen 2m, Gen 2x, and Gen 3.
Support 5 SATA
Support AHCI1.0 mode
Support for native command queue (NCQ)
Support FIS based on port multiplier switch or command switching.
Support hot swap and hot swap.
Compatible with SATA 6G, 3G and 1.5G hard drives
Bus interface: PCI-Expre X4 slot
Expansion interface: 5 SATA3.0 interfaces
System Requirements: One PCI Express X4 slot is available, supporting both PCI-E X2 X4 X8 X16
Operating system: Windows10/8/7 (32/64 bit) / Vista (32/64 bit) / 2003/2008/linux
Main chip: JMB585
The PCIE to SATA3.0 riser card is used as follows:
First, the system disk and PCIE to SATA3.0 riser card connection conditions and solutions:
1. The SATA interface mode of PCIE to SATA3.0 is AHCI mode. If you want to plug in the system disk on our card, the premise is that your system disk must be installed in AHCI mode when installing the system on the motherboard. Otherwise, it will not pass. Our card riser card starts the system.
2. If it is determined that the SATA interface installation system of the system disk inserted in the motherboard is AHCI mode, then you can directly insert the hard disk into our card, and then enter the motherboard BIOS to set the system disk as the first boot.
3, the above two conditions are available, if it still can not start, or repeated reboots, then the motherboard's hard disk interface and our adapter card conflict, the solution is to enter the motherboard BIOS, set the motherboard's hard disk interface options to Disabled, save and restart to start the system
Second, the common disk and PCIE to SATA3.0 connection conditions and solutions:
1. When the system disk is plugged into the motherboard, the ordinary disk is inserted in the PCIE to SATA3.0 card, then only the adapter card information and the ordinary disk model need to be detected at startup.
2, if the condition is established, or can not start the system, then you must enter the motherboard BIOS, set the system disk to the first boot.
Third, the system disk and the ordinary disk and PCIE to SATA3.0 connection and solution:
1. Prerequisites, if the system disk with the motherboard installed system is AHCI mode test, can use the following methods to achieve, if it is IDE mode installed system, then you can only reinstall the system through PCIE to SATA3.0 .
2, 1 condition is established, you can not start to enter the motherboard BIOS, set the system disk to the first boot.
3, 1.2 conditions are met, or can not start, then it may be integrated SATA interface conflict, please enter the motherboard BIOS to set SATA to Disabled
You'll receive:
1 x SATA III (6Gbps) 5-port PCI-Express Controller Card
1 x Low Profile Bracket
5 x Red SATA Cable
Please check pictures for more details.