P1 POORT DUTCH SLIMME METER KABLE FT232RL CHIP USB TO UART TTL 5V RJ11 RJ12 6P4C CABLE WITH DOMOTICZ ON RASPBERY

P1 POORT DUTCH SLIMME METER KABLE FT232RL CHIP USB TO UART TTL 5V RJ11 RJ12 6P4C CABLE WITH DOMOTICZ ON RASPBERY
Compatibility for P1 POORT DUTCH SLIMME METER: Kaifa MA105 en MA304 / ISKRA AM550 / SagemcomXS210 / Kamstrup 162, 382 en 351 / LANDIES E350 E360 / Iskra ME383 en MT 382 / Sagemcom T211
Imported chips, the quality is absolutely guaranteed, 100% inspection before shippment.
Wire gauge: UL2464 AWG28 8/ 0.12TS *4C+AL, UL certified wire, fire-resistant and flame-retardant, -25 ~ 80.
Outer diameter (OD): 4.0 mm
Jacket material: PVC
Wire material: tinned copper
Operating Systems:
Windows
10/8/ 8.1 /7/Windows Server 2008/2003/Vista/XP/98
Linux
Mac
OS X/9/8
Windows
CE. NET (Version 4.2 and greater)
Android
32 and 64 bit operating systems are both supported.
DRIVER DOWNLOADING:
https: //chip. com/drivers/vcp-drivers/
INSTALLATION GUIDELINE:
https: //chip. com/document/installation-guides/
Package Contents:
1 X USB to RJ11 Cable
Length: 0.6M, 1.5M, 1.8M, 3.0M, 3.6M
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing.
If you have special requirements, such as cable length, wire gauges and pinouts, please consult to me online or leave me a message.
If you receive the goods, and have any dissatisfaction or need assistance, please feel free to contact me or leave me a message.
Schematische voorstelling P1 poort (ESM
Rv 5.0 P1)
Moving to our house gave us the advantage of a energy meter for electricity, clean installed with counters starting from zero. Luckely for us they installed a Smart Meter type. These type of meters have a lot of smart ports, and one of them is the P1 port. Through this port it is possible to read the data from this meter. The P1 port is working according DSMR- 4.0.
Interface
The data from the P1 port is serial data, and is connectable with a RJ-11 connector, and
has the following signals:
1 N/A
2 RTS
3 GND
4 N/A
5 RxD
6 N/A
use a OLOEY Basic Breakout 5V to convert the serial. And am using it as a serial to USB converter to connect to my small FIT-PC2 server.
The interface should be conncted as follows:
P1. RTS to. VCC (5V)
P1. GND to. GND
P1. RxD to. RxI
NOTE 1: With this type of meter it is important to add a pull-up resistor between VCC and RxD. This is because the electronic of this smart-meter is an open collector connection.
NOTE 2: Because the Smartmeter has 0V for a logical 1 and a +5V for a logical 0, we need to invert the data signal, RxD. This can be done hardwarematically, but an easier solution in this case is in the SparkFun itself! This should be done with the program FT_Prog.
Please be kind to read the following information before you buying this cable,
Pinout P1-poort Kamstrup 162, 382 en 351
1 RTS (Request to Send)
2 GND (Ground)
3 NC (Not Connected)